Minuteman E26ECO_H26ECO Walk-Behind Scrubber Traction Drive User Manual

User ManualE26ECO/H26ECO Walk-Behind ScrubberTraction Drive Disc Deck

10Machine OverviewA BAIL HANDLEB HANDLE ADJUSTMENT KNOBC KEY SWITCHD DIRECTION SWITCHE SQUEEGEE LIFT LEVERF BATTERY / FAULT GAUGEG SPEED CONTROLH CHAR

11Machine OverviewBail Handle(A) When the scrub deck is lowered to the floor, the bail handle enables the brush motor and moves the machine forward on

12Machine OverviewMinuteman offers an optional hour meter for theE26ECO/H26ECO. The optional kit replaces thepower cord mounting bracket at the rear

13Machine OverviewCircuit BreakersA Main Control Circuit Breaker - 4AB Brush Motor Circuit Breaker - 30AC Vacuum Motor Circuit Breaker - 20AD Drive Mo

14Machine OverviewThe battery compartment is located under the recovery tank. TheBattery compartment can be accessed for servicing and mainte-nance by

15Machine OverviewWhen an error or fault occurs within the machine, a faultcode will appear on the battery gauge represented by aspecified number of f

16Machine OverviewHandle AdjustmentThe E26ECO/H26ECO handle was designed with operator comfortin mind. The angle and horizontal position of the handl

17Machine Overview123Plate Position 1(Shipping Position)Plate Position 2Plate Position 3(Fully Extended)Horizontal AdjustmentThe horizontal position c

18Machine OverviewSolution Tank Drain HoseThe solution tank may be drained by removing the Solution Tank DrainHose (A) from the Hose Barb (B) and rout

19Machine OverviewThe Solution Fill Filter (B) should be cleaned regularly.To remove, simply open the Solution Tank Lid (A) andpull the filter out.Sol

2This manual is furnished with each new MINUTEMAN E26ECO/H26ECO. This provides the necessary operating and preventivemaintenance instructions. Operato

20Machine OverviewScreened FloatIf the recovery tank (C) is overfilled or a large amount of foaming ispresent, the screened float (B) blocks the vacuu

21Machine OverviewScreened Float RemovalThe screened float is positioned between the vacuum manifold (A)and recovery tank (C). The screened float (B)

22Machine OverviewABDCThe solution solenoid, which shuts off solution flow when the bail handle is released, is protected from debris by the in-line f

23Machine OverviewRear SqueegeeA SqueegeeB Star-shaped knobC Adjusting screw for angle adjustmentD Suction hoseE Blade fastening latchF Washers for ca

24Machine OverviewThe angle adjustment is the decisive factor inensuring that the squeegee blades on thesqueegee lie evenly on the floor.1. Park the m

25Machine OverviewIf streaks are present, despite an optimumangle adjustment, the clearance between thecaster wheels and floor must be adjusted bychan

26Machine Overview1. Brush Deck may be tilted up for easierbrush installation/removal & to clearsteep ramps. Lift the handle on theupper lever w

27Machine OverviewIn order to consistently conserve water when using Aquastop brushes, the guide will stop the solution control lever at alow rate set

28This machine was designed with total operator comfort and ease of use in mind. All machine components have been designedas a total system to efficie

29WARNING!- Be sure you understand the machine controls and their functions.- While on ramps or inclines, avoid sudden stops when tanks are filled.- A

3Model E26ECO/H26ECOModel No. E26ECOQP, E26ECOQPG, H26ECOQP, H2ECOQPG40 amps140Ah @ 20 hr95Ah @ 20 hrE26ECO 69 dBA / H26ECO 65.5 dBA26 in (65 cm)38 in

30Machine OperationTo Turn ON Machine:Turn key to operate position ( I ). Wait for battery gauge to stop flashing, approximately 5 seconds. (If flas

31Machine OperationTo Charge Batteries:When the battery / fault gauge reaches the red zone the batteries need to be recharged. Take the machine to a

32After UseAfter Use1. When finished scrubbing, lift the scrub deck. Lift the rear squeegee (the vacuum motor will turn off after 10 seconds).Move the

33MaintenanceHave a qualified service technician check the vacuum motor carbon motor brushes once a year or after 300 operating hours.The brush motor

34TroubleshootingProblem Possible Cause Remedy Poor water pick-up Worn or torn squeegee blades Rotate or replace blades Recovery tank full Empty re

35TroubleshootingProblem Possible Cause Remedy Machine does not operate Tripped Control Power circuit breaker Reset circuit breaker Batteries have l

36TroubleshootingThe battery needs charging, there is a badconnection to the battery or dependent onprogramming, may indicate that the batterylockout

37TroubleshootingNot used.The controller is being inhibited from driving,this may be because the battery charger isconnected.The bail handle was activ

38Minuteman International Made Simple Commercial Limited WarrantyREVISION F EFFECTIVE 6/1/2009Minuteman International, Inc. warrants to the original p

39Cord Electric Group: Three years parts, two years labor, ninety days travel (Not to exceed two hours)Exceptions……….Model Parts Labor Poly TravelPor

4Safety InstructionUnpacking InstruInspection ...Electrical ...Batteries ...Operator ResponsMachine OvervieControls ...

Minuteman International · 14N845 U.S. Route 20 · Pingree Grove, Illinois 60140 USAPhone 800-323-9420 · Fax 800-422-6933www.minutemanintl.comA Member

5Table Of ContentsSafety Instructions ... 6Unpacking Instructions .

6Safety InstructionsIMPORTANT SAFETY INSTRUCTIONSOperators must read and understand this manual before operating or maintaining this machine.Do not op

7InspectionCarefully unpack and inspect your E26ECO/H26ECO Walk-Behind Scrubber for shipping damage. Follow unpackinginstructions on shipping pallet.

8Machine OverviewBACDEHGFGMachine OverviewA CUP HOLDERB SOLUTION FILL PORTC RECOVERY TANK LIDD RECOVERY TANKE BRUSH DECKF FRONT WHEEL (see note)G REAR

9Machine OverviewGAMBNHDFCDELJKMachine Overview - RearA BAIL HANDLEB SQUEEGEE LIFT LEVERC RECOVERY TANK DRAIN HOSED ONBOARD CHARGER CORDE CI