Minuteman E17_E20_H20 Walk-Behind Scrubber Disc Traction Dri User Manual

User ManualE17/E20/H20 Walk-Behind ScrubberDisc Brush Drive

10Machine OverviewControl PanelABCDFEGA BAIL HANDLEB HANDLE ADJUSTMENT KNOBC KEY SWITCHD SQUEEGEE LIFT LEVERE SOLUTION CONTROL LEVERF BATTERY GUAGEG C

11Machine OverviewBail Handle(A) When the scrubdeck is lowered to the floor, the bail handle enables the brush motor and moves the machineforward once

12Machine OverviewOptional Hour MeterMinuteman offers an optional hour meter for thismachine. The optional kit replaces the power cordmounting bracke

13Machine OverviewBattery CompartmentCircuit BreakersA Main Control Breaker - 4AB Brush Motor Breaker - 30AC Vacuum Motor Breaker - 20AThe circuit bre

14Machine OverviewRear SqueegeeA SqueegeeB Star-shaped knobC Adjusting screw for angle adjustmentD Suction hoseE Blade fastening latchF Washers for ca

15Machine OverviewThe angle adjustment is the decisive factor inensuring that the squeegee blades on thesqueegee lie evenly on the floor.1. Park the m

16Machine OverviewIf streaks are present, despite an optimumangle adjustment, the clearance between thecaster wheels and floor must be adjusted bychan

17Machine OverviewHandle AdjustmentThe handle was designed with operator comfort in mind. Theangle and horizontal position of the handle can be adjus

18Machine Overview123Plate Position 1(Shipping Position)Plate Position 2Plate Position 3(Fully Extended)Horizontal AdjustmentThe horizontal position c

19Machine OverviewIn order to consistently conserve water when using Aquastop brushes, the guide will stop the solution control lever at alow rate set

2This manual is furnished with each new MINUTEMAN E17/E20/H20. This provides the necessary operating andpreventive maintenance instructions. Operators

20Machine OverviewThe solution tank may be drained by removing the Solution Tank DrainHose (A) from the Hose Barb (B) and routing the hose to a floor

21Machine OverviewThe Solution Fill Filter (B) should be cleaned regularly.To remove, simply open the Solution Tank Lid (A) andpull the filter out.ABS

22Machine OverviewScreened FloatIf the recovery tank (C) is overfilled or a large amount of foaming ispresent, the screened float (B) blocks the vacuu

23Machine OverviewScreened Float RemovalThe screened float is positioned between the vacuum manifold (A)and recovery tank (C). The screened float (B)

24Machine OverviewRecovery Tank Drain HoseTwist Cap to Open and Drain Twist & Lift cap to clean outlarge debrisDeck Skirt Removal(Do not lower wit

25Machine OverviewABDCThe filter assembly is located at the rear of the machine on the left hand side, just under the solution tank. It is important

26The E17/E20/H20This machine was designed with total operator comfort and ease of use in mind. All machine components have been designed as a totalsy

27Machine OperationTo Turn on MachineTurn key to operate position ( I )To Turn on VacuumLower squeegee into operate position, vacuum motor will turn o

28Machine Operation1. To load the brush, first center theE17/E20 brush deck over thescrub brush.2. Lower the scrub deck by releasingthe deck lift peda

29Machine OperationUnloading Brush3. When done correctly the brushshould release from the scrub deckand fall to the floor.1. To unload the brush, firs

3Technical SpecificationsModel E17/E20/H20All Models Beginning with: E17BD / E20BD / H20BDE20BD / H20BD32 amps69 dBA / 65.5 dBA20 in (51 cm)34 in (86

30After UseAfter Use1. When finished scrubbing, lift the scrub deck and turn the solution lever off. Lift the rear squeegee. Move the machineto a serv

31Have a qualified service technician check the vacuum motor carbon motor brushes once a year or after 300 operating hours.The brush motor and transax

32Problem Possible Cause Remedy Poor water pick-up Worn or torn squeegee blades Rotate or replace blades Recovery tank full Empty recovery tank

33TroubleshootingProblem Possible Cause Remedy Vacuum motor does not turn on Recovery tank full Empty recovery tank Excessive foaming in recove

34Minuteman International Made Simple Commercial Limited WarrantyREVISION F EFFECTIVE 6/1/2009Minuteman International, Inc. warrants to the original p

35Cord Electric Group: Three years parts, two years labor, ninety days travel (Not to exceed two hours)Exceptions……….Model Parts Labor Poly TravelPor

Minuteman International · 14N845 U.S. Route 20 · Pingree Grove, Illinois 60140 USAPhone 800-323-9420 · Fax 800-422-6933www.minutemanintl.comA Member

4CE Declaration

5Table Of ContentsHandle Adjustment ... 17Angle Adjustment ...

6Safety InstructionsIMPORTANT SAFETY INSTRUCTIONSOperators must read and understand this manual before operating or maintaining this machine.Do not op

7InspectionCarefully unpack and inspect your E17/E20/H20 Walk-Behind Scrubber for shipping damage. Follow unpacking instructionson shipping pallet. Ea

8Machine OverviewMachine Overview - FrontA SPRAY BOTTLE / CUP HOLDERB SOLUTION FILL PORTC RECOVERY TANK LIDD RECOVERY TANKE BRUSH DECKF FRONT WHEELG R

9Machine OverviewMachine Overview - RearA BAIL HANDLEB SQUEEGEE LIFT LEVERC SOLUTION CONTROL LEVERD RECOVERY TANK DRAIN HOSEE ONBOARD CHARGER CORDF CI